2013-09-07 11:21:23 -04:00
|
|
|
ACreal IO
|
|
|
|
|
========
|
|
|
|
|
ACreal IO is a firmware code for Arduino to build Konami ACIO compatible boards.
|
|
|
|
|
|
|
|
|
|
Konami ACIO is a protocol used for communication between arcade games and harware components such as e-Amusement readers.
|
|
|
|
|
Its uses rs232 and allows several "nodes" to be connected a single serial port.
|
|
|
|
|
|
|
|
|
|
Games support
|
|
|
|
|
-------------
|
2013-11-19 16:28:07 -05:00
|
|
|
Currently this project supports the following games :
|
2013-09-07 11:21:23 -04:00
|
|
|
|
|
|
|
|
pop'n music 15-18 (one old slotted reader)
|
2013-09-07 11:32:17 -04:00
|
|
|
|
2020-02-22 07:54:34 -05:00
|
|
|
pop'n music 19-25 (one new wavepass reader with encrypted communication (only game I know which uses this encryption) + optional card dispenser)
|
2013-09-07 11:32:17 -04:00
|
|
|
|
2013-09-07 11:21:23 -04:00
|
|
|
iidx 13-18 (2 old slotted readers)
|
2013-09-07 11:32:17 -04:00
|
|
|
|
2013-09-07 11:21:23 -04:00
|
|
|
iidx 19-20 (2 new wavepass readers)
|
2013-09-07 11:32:17 -04:00
|
|
|
|
2013-09-07 11:21:23 -04:00
|
|
|
jubeat 1 - knit (one old slotted reader (no keypad) + one led board (game won't boot if the led board is not present)
|
2013-09-07 11:32:17 -04:00
|
|
|
|
2013-09-26 13:15:22 -04:00
|
|
|
jubeat copious - saucer (one new reader (no keypad) + one led board (game won't boot if the led board is not present)
|
|
|
|
|
|
2013-11-19 16:28:07 -05:00
|
|
|
DDR SN-SN2 (2 old slotted readers)
|
|
|
|
|
|
|
|
|
|
DDR X-X3 (2 readers (old or new) in sd, 2 readers (old or new) + led board ? in HD)
|
2013-09-07 11:32:17 -04:00
|
|
|
|
2013-09-07 11:21:23 -04:00
|
|
|
drum mania (1 old reader)
|
2013-09-07 11:32:17 -04:00
|
|
|
|
2013-09-07 11:21:23 -04:00
|
|
|
guitar freaks (2 old readers)
|
2013-09-07 11:32:17 -04:00
|
|
|
|
2020-02-22 07:54:34 -05:00
|
|
|
Sound voltex (1 new wavepass reader + 1 IoBoard )
|
|
|
|
|
|
|
|
|
|
How to use
|
|
|
|
|
----------
|
|
|
|
|
|
|
|
|
|
Flash the firmware on an arduino mega 2560, scratch the "reset-en" bridge on the pcb, change COM port to COM1
|
|
|
|
|
|
|
|
|
|
PN5180 support
|
|
|
|
|
--------------
|
|
|
|
|
|
|
|
|
|
Currently a single PN5180 nfc module is supported.
|
|
|
|
|
You can set #define RFID_MODULE1 3 in pinoutconfig to use it.
|
|
|
|
|
|
|
|
|
|
Arduino | PN5180 pin mapping:
|
|
|
|
|
--- | ---
|
|
|
|
|
5V | 5V
|
|
|
|
|
3.3V | 3.3V
|
|
|
|
|
GND | GND
|
|
|
|
|
SCLK,52 | SCLK
|
|
|
|
|
MISO,50 | MISO
|
|
|
|
|
MOSI,51 | MOSI
|
|
|
|
|
SS,10 | NSS (=Not SS -> active LOW)
|
|
|
|
|
BUSY,9 | BUSY
|
|
|
|
|
Reset,7 | RST
|
|
|
|
|
|
|
|
|
|
SS, BUSY and Reset pins can be changed in pinoutconfig.h
|
